Hitek Systems
The HiPrAcc NC100 is the highest network and PCIe performance low profile PCIe Data Center accelerator card with Intel’s 10nm Agilex FPGA. Only module with 200Gbps (4x56Gbps PAM-4) Ethernet interface and 16x PCIe Gen4 support.
|
|
 |
Features
- PCIe low profile (half-length, half-height) form factor (6" x 2.46")
- Available with single-slot and double-slot passive and active cooling configurations
- Agilex AGF014 and AGF012 device support
- 16x PCIe Gen4 (256Gbps) host interface
- Up to 200Gbps network interface via single zQSFP 56Gbps PAM4 and 28Gbps NRZ
- 3 banks of 64-bit DDR4 memory (12GB/24GB)
- Agilex ARM HPS support with 16/32GByte eMMC and option for direct GigE network interface to HPS (requires full-height bracket with RJ-45 adapter)
- Up to 75W card load with edge power and up to 125W card load with 6-pin PCIe power connector
- Integrated USB Blaster II, Agilex debug and module monitor interfaces through a single micro-USB connector on PCIe bracket
- Flexible clocking architecture with support for external synchronization/clock interface
- Extensive power, voltage and temperature telemetry with SMBus based access for host server board management controller (BMC)
-
Open FPGA Stack, OpenCL and oneAPI support for high level abstracted development flow
Target Applications
- Designed for Data Center workloads and scale out architectures
- Bump-in-Wire networking and high-performance computing
- Intelligent network controller for GPU farms
- Machine learning, network, compute and storage acceleration
Interfaces
- x16 Gen4 PCIe card edge Interface
- Backwards compatible with Gen3
- Supports bifurcation as two x8 Gen4/Gen3
- Gen2 and Gen1 supported via link down-training
- zQSFP+ (QSFP56) Network interface port
- PAM4: 1x 200G (Soft IP, 4 lanes)
- PAM4: 2x 100G (E-Tile hard IP, 2 lanes per port)
- PAM4: 4x 50G (Soft IP, 1 lane per port)
- NRZ: 1x 100G (Soft IP, 4 lanes)
- NRZ: 2x 50G (Soft IP, 2 lanes per port)
- NRZ: 1x 50G (Soft IP, 4 lanes)
- NRZ: 1x 40G (Soft IP, 4 lanes)
- NRZ: 4x 25G/10G (E-Tile hard IP
Hardware verified 200G/100G/50G/40G Soft IP Cores available from Hitek Systems
- Unified micro-USB 2.0 interface with on-board USB hub for:
- Integrated USB Blaster II
- UART interface to HPS or FPGA fabric (DIP switch selectable)
- UART interface to module control CPLD for card monitor and control
- 14-pin header for HPS GigE network interface (requires full-height bracket with RJ-45 adapter)
- SMB coaxial connector for external clock/PPS reference input
Memory, Storage and Configuration Interfaces
- Three 64-Bit DDR4 interfaces, 4GB or 8GB each component memory
- One DDR4 port routed to HPS accessible banks
- 16/32GByte eMMC storage device for HPS
- 2Gbit QSPI flash for FPGA configuration connected to the module control CPLD
- x8 AVST configuration interface from module control CPLD
- 64Mbit QSPI flash for module control CPLD and BMC controller
On-board Development and Debug Support
- Integrated USB Blaster II
- UART access to the FPGA and module control CPLD
- Temperature, voltage and current monitoring sensors to module control CPLD
- Module input power measurement for profiling and verification in target servers/environment
- Automatic over-temp FPGA de-configuration
- Support for server Board management controller (BMC) with MTCP protocol support via SMBus through integrated module control CPLD processor (Planned)
- 4 bi-color LEDs for network port interface status
- Tri-color module status LED at PCIe bracket edge
- Multiple on-board diagnostic and status LED
Power and Heatsink Options
- Options for edge power or 6-Pin PCIe connector power input
- Options for single-slot and double-slot passive and active heat sinks
- 75W with PCIe edge power
- 125W with double slot 6-pin PCIe connector power